How Much Does Attic Insulation Cost?
Attic insulation costs $1,700 to $2,500 installed for most homes, averaging about $2,100, according to HomeAdvisor and Angi's 2026 data. Per square foot of attic floor, the price runs $1 to $3 for blown-in material — the cheapest way to add insulation — while spray foam under the roof deck can reach $3 to $5 per square foot, and a full roof-deck job can pass $9,000.
Insulation is the cheapest energy upgrade most houses will ever get, and it is also where quotes vary the most. Two numbers decide the price — the material and the R-value, the measure of how much heat the insulation resists — and most quotes only show one of them.
Attic Insulation Cost at a Glance
The table below shows typical prices in the United States, checked Nov 11, 2026 (sources: HomeAdvisor, Angi, HomeGuide, and contractor-bid data from the NRCA).
| Item | Typical cost |
|---|---|
| National average | About $2,100 |
| Most projects | $1,700–$2,500 |
| Per square foot (blown-in) | $1–$3 |
| Blown-in top-up, 1,500 sq ft | $1,800–$2,800 |
| Removal of old insulation | $1–$2 per sq ft |
| Air sealing | $250–$3,000 |
| Spray foam roof deck | $1,500–$9,000 |
HomeAdvisor and Angi publish from the same survey data, so treat them as one source: both put the average at $2,100 and most jobs between $1,700 and $2,500. HomeGuide gives a wider $1,000 to $2,700, with a low of $500 and a high of $6,000 for unusual jobs.
R-Value by Climate Zone: The Number That Sets the Price
R-value measures resistance to heat flow — higher means better insulation. ENERGY STAR recommends different R-values depending on where you live, and the target decides how much material the job needs.
| Climate zone | Recommended R-value | Blown fiberglass depth |
|---|---|---|
| Zones 1–2 (hot: Florida, south Texas, Hawaii) | R-30–R-49 | 8–14 inches |
| Zone 3 (warm: Georgia, north Texas, Carolinas) | R-30–R-60 | 8–17 inches |
| Zones 4–8 (cold: New York, Chicago, Minneapolis) | R-49–R-60 | 14–20 inches |
The depth column is the part most guides skip. A quote that says "$1.50 per square foot" means nothing until you know the depth: blown fiberglass gives about R-2.2 to R-2.7 per inch, so R-49 needs roughly 18 inches of it, while cellulose at R-3.2 to R-3.8 per inch reaches the same R-value at about 14 inches. Two quotes at the same per-square-foot price can deliver very different R-values — and the cheaper one is usually the thinner one.
Cost by Material
Six materials cover nearly every attic job. The R-value per inch and the installed price move together — the materials that insulate best per inch cost the most per square foot.
| Material | R-value per inch | Installed per sq ft |
|---|---|---|
| Blown-in cellulose | 3.2–3.8 | $1.00–$2.50 |
| Blown-in fiberglass | 2.2–2.7 | $1.00–$2.00 |
| Fiberglass batts | 2.9–3.8 | $1.60–$2.20 |
| Mineral wool batts | 3.0–3.3 | $1.90–$2.60 |
| Open-cell spray foam | 3.5–3.7 | $1.50–$3.00 |
| Closed-cell spray foam | 6.0–6.5 | $3.00–$5.00 |
Blown-in cellulose is the best overall pick for most attics: it fills irregular gaps, costs $1.00 to $2.50 per square foot installed, and its borate fire retardant gives it a Class I fire rating. Fiberglass batts are the budget DIY option at $0.50 to $1.50 per square foot for materials alone — but batts leave gaps around every cut, and gaps are where heat escapes. Closed-cell spray foam is the premium choice at $3.00 to $5.00 per square foot: at R-6.0 to R-6.5 per inch it is the only material that also acts as an air and moisture barrier, which is why it is the pick for conditioned attics.
Contractor-bid data from the NRCA puts the same materials in a tighter band for a straightforward top-up: blown cellulose $1.20 to $1.50 per square foot installed, blown fiberglass $1.40 to $1.85, fiberglass batts $1.60 to $2.20, and mineral wool batts $1.90 to $2.60. The wider HomeAdvisor ranges cover difficult attics too.
What Else Moves the Price
Three add-ons decide whether a job lands at the low or high end of the range — and two of them are usually missing from the first quote.
Removing old insulation is the first. If the existing insulation is wet, mouldy, or contaminated with droppings, it has to come out before new material goes in. Professional removal runs $1 to $2 per square foot, or about $600 to $1,200 for a standard attic — roughly $900 on average (HomeAdvisor, 2026). A crew with a vacuum truck does it in a day.
Air sealing is the second, and the one that pays for itself fastest. Insulation slows heat; air sealing stops it. Gaps around pipes, wires, light fixtures, and the attic hatch leak warm air straight past the insulation, and sealing them costs $250 to $3,000. Insulation without air sealing is a thicker blanket on a bed with the window open.
Access is the third. The NRCA's 2026 contractor-bid data shows three labour bands: an easy walk-up attic with no obstructions runs $0.95 to $1.10 per square foot in labour; normal pull-down ladder access runs $1.20 to $1.50; and a difficult attic — knee walls, low pitch, HVAC equipment in the way — runs $1.65 to $2.20. Labour is 60 to 70 percent of a blown-in job, so access alone can move the total by a third.
The 25C Tax Credit Has Ended — Do Not Count On It
Here is the freshness trap in this market, and it matters because one live price calculator still gets it wrong.
The federal 25C energy-efficient home improvement credit covered 30 percent of insulation material costs, up to $1,200 a year, for work completed through December 31, 2025. It expired on that date under the One Big Beautiful Bill Act and was not renewed for 2026. ENERGY STAR and the IRS both confirm it: the credit does not apply to work done in 2026.
One popular attic-insulation cost calculator still states that the credit was "extended by the Inflation Reduction Act through 2032" — that is wrong, and any quote that subtracts the credit from a 2026 job is using last year's rules. What replaced it is the HEAR rebate program, up to about $1,550 to $1,650 for insulation and air sealing, and the HOMES rebate program, up to about $7,760 to $8,240 — but both are income-qualified and administered state by state. Check your state energy office before budgeting, and do not count on the money until the rebate is confirmed in writing.
A Worked Example: 1,500 Square Feet, R-19 to R-49
Take a 1,500-square-foot attic topped up from R-19 to R-49 with blown-in cellulose, standard access, no removal needed.
| Line item | Cost |
|---|---|
| Blown cellulose, $1.35 per sq ft × 1,500 sq ft | $2,025 |
| Air sealing (hatch, pipes, fixtures) | $400 |
| Total | $2,425 |
That sits inside the $1,800 to $2,800 band the NRCA data gives for a 1,500-square-foot blown-cellulose top-up. The same attic in blown fiberglass would cost $2,400 to $3,600. Upgrading to closed-cell spray foam under the roof deck instead would start around $4,500 — and the payback on the extra spend is measured in decades, not years, which is why blown-in wins for most homes.
Mistakes to Avoid
- Comparing quotes without an R-value. A price per square foot means nothing until you know the depth and the R-value it delivers. Ask every contractor for the target R-value in writing.
- Counting on the 25C credit. It expired December 31, 2025. A quote that subtracts it is using last year's rules.
- Skipping air sealing. Insulation without air sealing leaves the biggest leaks open. Seal first, insulate second.
- Choosing batts for an irregular attic. Batts leave gaps around every joist, wire, and pipe. Blown-in fills them.
- Paying for removal you do not need. Dry, clean old insulation can usually stay — new material goes straight on top. Removal is only needed when it is wet, mouldy, or contaminated.
Frequently Asked Questions
How much does attic insulation cost?
About $2,100 on average, checked Nov 11, 2026, with most projects between $1,700 and $2,500. The rate is $1 to $3 per square foot installed for blown-in material, and $3 to $5 for closed-cell spray foam.
What R-value does my attic need?
ENERGY STAR recommends R-30 to R-49 in hot climates (zones 1–2), R-30 to R-60 in warm climates (zone 3), and R-49 to R-60 in cold climates (zones 4–8). Most existing attics are under-insulated — topping up to R-49 is the usual target.
Is blown-in or batt insulation cheaper?
Blown-in cellulose is cheaper installed, at $1.00 to $2.50 per square foot, against $1.60 to $2.20 for fiberglass batts. Batts are cheaper as materials alone ($0.50 to $1.50 per square foot) but leave gaps that blown-in fills.
Is spray foam worth it for an attic?
Only for a conditioned attic, where the foam's air and moisture barrier matters. At $3.00 to $5.00 per square foot installed, closed-cell spray foam costs two to three times blown-in for the same attic, and the payback is measured in decades.
Is the federal insulation tax credit still available?
No. The 25C credit, 30 percent of material costs up to $1,200 a year, expired on December 31, 2025. The HEAR and HOMES rebate programs replaced it for income-qualified households, administered state by state.

